Home | ENGINEERING | Direct instrument measurements

Mechanical - Metrology and Measurements - Thread Measurement

Direct instrument measurements

   Posted On :  23.09.2016 09:34 pm

Some of the direct measurement instruments are 1. Stylus probe instruments. 2. Tomlinson surface meter. 3. Profilometer. 4. Taylor-Hobson Talysurf

Direct instrument measurements

 

Direct methods enable to determine a numerical value of the surface finish of any surface. These methods are quantitative analysis methods and the output is used to operate recording or indicating instrument. Direct Instruments are operated by electrical principles. These instruments are classified into two types according to the operating principle. In this is operated by carrier-modulating principle and the other is operated by voltage-generating principle, and in the both types the output is amplified.

 

 

Some of the direct measurement instruments are

 

1. Stylus probe instruments.

 

2. Tomlinson surface meter.

 

3. Profilometer.

 

4. Taylor-Hobson Talysurf

 

 

1.     Stylus probe type instrument

 

 

Principle

When the stylus is moved over the surface which is to be measured, the irregularities in the surface texture are measured and it is used to assess the surface finish of the work piece.


 

Working

 

The stylus type instruments consist of skid, stylus, amplifying device and recording device. The skid is slowly moved over the surface by hand or by motor drive. The skid follows the irregularities of the surface and the stylus moves along with skid. When the stylus moves vertically up and down and the stylus movements are magnified, amplified and recorded to produce a trace. Then it is analyzed by automatic device.

 

Advantage

 

Any desired roughness parameter can be recorded.

 

Disadvantages

 

1. Fragile material cannot be measured.

 

2. High Initial cost.

 

3. Skilled operators are needed to operate.

 

 

2. Tomlinson Surface meter

 

This instrument uses mechanical-cum-optical means for magnification.

 

Construction

In this the diamond stylus on the surface finish recorder is held by spring pressure against the surface of a lapped cylinder. The lapped cylinder is supported one side by probe and other side by rollers. The stylus is also attached to the body of the instrument by a leaf spring and its height is adjustable to enable the diamond to be positioned and the light spring steel arm is attached to the lapped cylinder. The spring arm has a diamond scriber at the end and smoked glass is rest  on the arm.


When measuring surface finish the body of the instrument is moved across the surface by a screw rotation. The vertical movement of the probe caused by the surface irregularities makes the horizontal lapped cylinder to roll. This rolling of lapped cylinder causes the movement of the arm. So this movement is induces the diamond scriber on smoked glass. Finally the movement of scriber together with horizontal movement produces a trace on the smoked glass plate and this trace is

 

magnified by an optical projector.

 

3. Profilometer


It is an indicating and recording instrument to measure roughness in microns. The main parts of the instrument are tracer and an amplifier. The stylus is mounted in the pickup and it consists of induction oil located in the magnet. When the stylus is moved on the surface to be tested, it is displaced up and down due to irregularities in the surface. This movement induces the induction coil to move in the direction of permanent magnet and produces a voltage. This is amplified and recorded.

 

4. Talyor-Hobson-Talysurf

 

It is working a carrier modulating principle and it is an accurate method comparing with the other methods. The main parts of this instrument is diamond stylus (0.002mm radius) and skid

 

 

 

Principle

 

The irregularities of the surface are traced by the stylus and the movement of the stylus is converted into changes in electric current.


Fig 3.26 Talyor-Honson Instrument

 

 

Working

 

On two legs of the E-shaped stamping there are coils for carrying an A.C. current and these coils form an oscillator. As the armature is pivoted about the central leg the movement of the stylus causes the air gap to vary and thus the amplitude is modulated. This modulation is again demodulated for the vertical displacement of the stylus. So this demodulated output is move the pen recorder to produce a numerical record and to make a direct numerical assessment.


Tags : Mechanical - Metrology and Measurements - Thread Measurement
Last 30 days 173 views
Related words :

What is Direct instrument measurements Define Direct instrument measurements Definition of Direct instrument measurements where how meaning of Direct instrument measurements lecturing notes for Direct instrument measurements lecture notes question and answer for Direct instrument measurements answer Direct instrument measurements study material Direct instrument measurements assignment Direct instrument measurements reference description of Direct instrument measurements explanation of Direct instrument measurements brief detail of Direct instrument measurements easy explanation solution Direct instrument measurements wiki Direct instrument measurements wikipedia how why is who were when is when did where did Direct instrument measurements list of Direct instrument measurements school assignment college assignment Direct instrument measurements college notes school notes kids with diagram or figure or image difference between Direct instrument measurements www.readorrefer.in - Read Or Refer

​TOP MENU

OTHER SUGEST TOPIC

Recent New Topics :